Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

金具零部件表面防腐蚀试验研究

随着经济的持续高速增长，各行业用电需求增大。在加快特高压骨干电网建设的同时，提高现有电网的输电能力、输电质量成为重中之重。金具是海上换流站的重要组成部分，海洋环境的特殊性，对金具提出了更高的耐腐蚀性能要求。为了探究海洋环境对金具的腐蚀性，选用ZL101A和ZL102两种典型的铝合金金具，采用5种辅助防腐蚀工艺获得5种耐腐蚀样本，并模拟海上工况对其分别进行盐雾腐蚀试验，得出最优防腐蚀工艺。研究表明：ZL101A和ZL102两种铝合金具有一定的耐腐蚀性能，ZL101A铝合金的耐腐蚀性能强于ZL102铝合金的；抛丸处理的防腐措施在ZL101A铝合金样本中的防腐蚀表现要强于ZL102铝合金样本的；阳极氧化在两种材质中防腐蚀表现均为优异，是最优异的防腐蚀工艺。     

公理化局部有限空间中映射连续性的扩展

用公理化方法研究了局部有限空间中的连续映射及其扩张问题。给出了局部有限空间的公理化定义方法;利用邻近关系研究了局部有限空间中的连续映射、同胚和局部同胚等问题;通过对局部有限空间变形的研究,定义了局部有限空间的一种特殊收缩核,有效地解决了局部有限空间中连续映射的扩张问题。     

大鼠血管内皮细胞siRNA转染条件的优化

目的:旨在优化siRNA转染大鼠血管内皮细胞的转染条件.方法:将0.75μL和1.5μL的脂质体LipofectamineTM3000分别与20、40、60、80nmol带荧光标记的FAMsiRNA组合,转染6、12、18、24h后,用荧光显微镜计数阳性细胞率、MTT法检测各浓度条件下内皮细胞的存活率,筛选最优转染条件.结果:(1)转染12h后,用荧光显微镜检测20、40、60、80nmol各组,均可观察到绿色荧光(2)siRNA浓度为60nmol/L,脂质体为1.5μL的组合转染效率最高,继续增加siRNA的浓度,转染效率提高不明显.(3)转染时间超过24h,各组细胞荧光减弱,细胞死亡率显著增加.结论:结果表明,以1.5μL LipofectamineTM3000与60nmol/L的siRNA浓度组成转染混合物转染12h可以实现对大鼠血管内皮细胞高效转染并保持较高的细胞活性.     

哺乳动物核移植研究进展

核移植技术具有重大的生物学的意义，特别是体细胞核移植技术的成功表明动物分化的体细胞核可再程序化，哺乳动物核移植的研究虽然还存在许多问题需要解决，但在挽救濒危动物，转基因动物研究，人类器官移植等许多方面展现了广阔的应用前景．     

智能高速罐身电阻焊机数字化控制系统

提出了以国产MCT80 0 0F8运动控制器为核心的智能高速罐身电阻焊机数字化控制系统 ,并介绍了系统的组成、工作原理、硬件接口、电机控制方法以及伺服电机的运动关系数学模型 .新的系统有利于提高罐身电阻焊机的制罐生产速度 ,并具有功能全面、可靠性高、控制精确、开放性好以及成本较低等优点     

PEMFC电催化剂利用率研究方法的探讨

提高电催化剂的利用率以降低质子交换膜燃料电池(PEMFC)的成本，是加速其商业化的一个重要途径。文中讨论了现有的CV法在研究PEMFC电催化剂利用率时存在的一些问题，如CV法扫描速度的影响及Pt理论比表面积难于准确确定等，为了较好地解决这一问题，提出了一种以单位质量电催化剂产生电池功率或电能来表示膜电极中电催化剂利用率的方法。     

NIPA类共聚温敏水凝胶中水的状态和耐热性

用N-异丙基丙烯酰胺（NIPA）与丙烯酸钠（SA）及甲基丙烯酸钠（SMA）共聚合成了两个系列的水凝胶，研究了共聚组成与水凝胶基本性质的关系，并用示差扫描量热法（DSC）和热失重法（TG）研究了此类水凝胶中水的状态和耐热性。